How to Measure Exterior Doors | SoCal Millworks

SoCal Millworks • Measuring Guide

How to Measure for an Exterior Door

A simple guide to collecting the measurements and photos we need for your entry-door quote.

Download Fillable Exterior Door Measuring Form (PDF)

Fill in the PDF on your computer or print a blank copy.

Before you start: Exterior door slabs, complete prehung door units, visible frame openings, and exposed rough openings are four different measurements. Please label each measurement rather than assuming they are interchangeable. This guide helps us prepare a quote; it does not replace a professional field measurement or the selected manufacturer's installation specifications.

SoCal Millworks exterior door measurement diagrams: door slab, framing rough opening, jamb depth, threshold and swing
Visual overview. Write down all measurements and photograph the actual door. SoCal Millworks confirms handing and manufacturer clearances before ordering.

Video tutorial

Watch How to Measure an Exterior Door

Exterior door measurement tutorial courtesy of Masonite, supplied to customers through the original third-party hosted video. Watch first, then complete the SoCal Millworks measurement form below.

Open Masonite Video

Watch the measuring tutorial above, then complete the SoCal Millworks measurement form below. Final LH/RH inswing/outswing handing is confirmed by SoCal Millworks.

View the Official Masonite Exterior Door Measuring Guide

Step 1 — Tell us what you are replacing

Are you replacing the door slab only while keeping the existing frame, or replacing the complete prehung unit (door, jamb/frame and threshold)? Tell us whether it is a single door, double/French entry door, or a door with sidelites or transom. Let us know if you need supply only or supply and installation.

Step 2 — Measure the existing door slab

With the door accessible, measure the slab width across the top, middle and bottom; measure height along both edges; and measure the door thickness. Write down all measurements in inches. For a slab-only replacement, photograph the hinge locations, latch/lock bore, weatherstripping, and existing threshold—these details must match or be reviewed.

Step 3 — Measure the existing frame and opening

Measure the clear opening between the inside jamb surfaces at the top, middle and bottom. Measure height between the underside of the head jamb and the threshold at both sides. Record the smallest width and height, but keep all actual readings. Then measure the overall exterior frame/unit size if its endpoints are accessible. Include the threshold and any brickmould in your photos; do not mistake trim-to-trim measurements for the unit or rough opening.

If framing is exposed, separately measure the rough opening between framing members at the top, middle and bottom and from the header to the supporting sill/subfloor. Do not remove trim just to obtain a measurement if you are not comfortable doing so. We can help determine what further verification is needed.

Step 4 — Check jamb depth and threshold

Measure the wall/frame depth from the interior side of the jamb to the exterior side, excluding decorative casing or brickmould. Note the existing threshold type and height, finished flooring, exterior landing, and whether there is tile, stucco, siding, or masonry adjacent to the frame. Photograph any rot, water damage, or unusual floor transitions.

Step 5 — Confirm handing and swing

First identify whether the door swings into the building (inswing) or out toward the exterior (outswing). For reference, note whether the hinges appear on the left or right in a photo taken from outside. This hinge-side observation helps us review the configuration, but it is not the final ordering designation.

Final handing selection: □ LH Inswing   □ RH Inswing   □ LH Outswing   □ RH Outswing

Take clear photos of the door partly open from both inside and outside. SoCal Millworks will verify the final LH/RH handing using the selected manufacturer’s convention before ordering.

Step 6 — Take photos for your quote

  • Entire exterior door and surrounding trim, photographed from outside and inside
  • Close-up of the threshold, bottom corners, and floor transitions
  • Close-up of hinges, latch, deadbolt, and weatherstrip
  • Tape measure showing slab width, height, thickness and jamb depth
  • Any sidelites, transom, brickmould, stucco, tile, damage or unusual conditions

Online Exterior Door Measurement Worksheet

Enter your measurements, then choose Submit Measurements to send them directly, or Print Form Only for a paper copy. You can also use the downloadable fillable PDF.

Customer details

Configuration

Door slab (inches)

Slab width
Slab height

Existing frame (inches)

Clear inside-jamb width
Clear frame height to threshold

Rough opening (only if exposed)

Framing width
Header to supporting sill/subfloor height

Jamb and threshold

Door handing

Reference hinge location viewed from outside:

Final requested handing (subject to verification):

Photos and comments

Submitting sends your measurements through the SoCal Millworks contact form. Your email address is required so we can respond. Shopify may ask you to complete a security check. Photos can be sent separately by text.

Please keep a copy using Print Form Only if desired. Photos are not included in the online submission; text them to (951) 314-4334 with your name.

Ready for an Exterior Door Quote?

Send us your measurements and photos. Our team can help confirm the right unit, frame depth, threshold, handing and product options before ordering.

Call: (951) 393-0333
Text photos: (951) 314-4334
Email: info@socalmillworks.com

Important: Final dimensions, required rough-opening clearances, threshold support, weatherproofing, flashing, swing, fire rating and installation conditions depend on the selected door unit and site. Do not order or cut an exterior door solely from the measurements on this guide. Fire-rated doors and assemblies require matching listed components and product-specific verification.