How to Install Interior Doors | Slab & Prehung Guide

SoCal Millworks · How-to Guide

How to Install an Interior Door

Follow the right path for your project: replace a door slab in an existing frame, or install a complete prehung door and frame.

Carpenter preparing an interior door slab

Start here · Before any work

What You'll Need

Gather the basic tools first. Then choose the instructions for your type of project.

For Either Project

  • Tape measure, pencil, level and square
  • Drill/driver, suitable bits and screwdrivers
  • Eye and hearing protection; dust control
  • Stable work supports, clamps and a helper for heavy doors
  • Door-specific manufacturer instructions and hardware

If Replacing a Slab

  • Existing door to use as a reference
  • Hinge screws and compatible lockset/latch
  • Track saw or other suitable cutting system, only if trimming is permitted
  • Hinge template/router or sharp chisels and a lock-boring jig, if preparation is needed

If Installing Prehung

  • Correct prehung unit and approved fasteners
  • Shims, suitable level and fastening tools
  • Trim-removal tools if replacing the existing jamb
  • Casing and finishing supplies as specified
Check before starting: Confirm handing, finished dimensions, door thickness, hardware, and manufacturer instructions. For prehung units, verify the specified rough opening and jamb depth. Never assume all slabs can be trimmed or modify a fire-rated assembly outside approved instructions.

Option 1 · Keep the existing frame

Replacing an Interior Door Slab

Use this method when your existing jamb is in good condition. Follow Steps 1–6 in order. Step 4 includes the four illustrated preparation tasks.

  1. 1

    Check the existing frame

    Confirm the jamb is secure, straight, and suitable to reuse. Check the existing door's swing and gaps.

  2. 2

    Measure the old slab

    Record actual width, height, thickness, handing, hinge locations, latch height, and floor clearance. Compare against the replacement.

  3. 3

    Remove the old door

    Support the slab, remove hinge pins or screws, and keep the old door as a reference for hardware layout.

  4. 4

    Prepare the new slab

    Use the four illustrated preparation tasks below only as needed. Always check trimming allowances and the actual hardware template.

    Door preparation: four illustrated tasks

    Follow the illustrated tasks below in the order needed for your door. Some replacement slabs arrive pre-sized or pre-bored, so only complete the work your door requires.

    Carpenter training illustration: Trim the width
    01 · Trim the width

    Keep the slab flat and fully supported. Mark the long edge, clamp the track parallel to that edge, and make a lengthwise cut within the manufacturer's permitted trimming allowance.

    Carpenter training illustration: Trim the height
    02 · Trim the height

    Mark the required finished height. With the slab flat, guide the saw across the short end—not down the long edge. Support the offcut and finish the exposed edge.

    Carpenter training illustration: Bore the handle and latch
    03 · Bore the handle and latch

    Check the hardware template, backset, handing, and centerline. Bore the face and edge holes using a secure jig, protecting the opposite face from breakout.

    Carpenter training illustration: Mortise the hinges
    04 · Mortise the hinges

    Transfer hinge locations from the existing jamb. Secure the slab on edge, rout or chisel shallow recesses, and test-fit hinge leaves flush.

    Safety: clamp and support the slab, use appropriate PPE and dust extraction, and keep clear of the blade path. Never exceed manufacturer trimming limits or modify fire-rated doors outside approved instructions.

  5. 5

    Hang and align the door

    Secure the hinges and support the slab as you hang it. Check consistent reveals, smooth swing, and floor clearance.

  6. 6

    Test the fit and latch

    Close the door and verify latch engagement. Correct alignment before removing any additional material; finish exposed edges per manufacturer instructions.

Option 2 · Replace the slab and frame

Installing a Prehung Interior Door

A prehung door arrives in its jamb. Use the manufacturer's exact rough-opening and fastening instructions for the specific unit.

  1. 1

    Check the rough opening

    Verify the manufacturer's rough-opening requirements, jamb depth, handing, swing, and the opening's plumb, level, and square.

  2. 2

    Remove the old frame if needed

    Carefully remove casing and the old jamb without damaging framing or hidden services.

  3. 3

    Position the prehung assembly

    With a helper, place the unit in the opening and align the jamb with the finished wall.

  4. 4

    Shim, plumb, and level

    Shim at specified points, keeping the hinge jamb straight and reveals even.

  5. 5

    Fasten the jamb

    Fasten into suitable framing using manufacturer-specified screws or nails, supporting fastening locations with shims.

  6. 6

    Test and finish

    Confirm swing and latch operation, trim protruding shims, install casing, and finish per the product instructions.

Watch: How to Install a Prehung Interior Door

Masonite installation video · Watch on YouTube
Important: Rough-opening allowances and installation methods vary by manufacturer. Do not rely on a universal opening-size rule.

Common questions

Before You Start

Can I replace just the slab?

Usually, if the existing frame is straight, sound, and the new slab can be prepared to match the opening, hinges, and latch.

What if the door rubs or won't latch?

Check hinge security, frame alignment, and reveals before cutting away additional material.

Does the $149 Trim & Fit service include installation?

No. It is a shop preparation service, not onsite installation.

Can I use this guide for fire-rated or exterior doors?

No. Those assemblies have specific listing, hardware, and installation requirements.

Ready for Your Project?

Find interior door slabs and prehung options, or request help with your project.

Browse Interior DoorsTrim & Fit ServiceRequest a Quote

General guidance for standard residential interior doors. Follow the manufacturer's instructions and applicable requirements. SoCal Millworks supplies primed doors, not painted doors.